Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Plano, TX
Most gate repair calls we take in Plano involve two things: a motor that stopped working, and a gate that no longer sits square in its opening. The second problem is usually the older one. Plano’s Blackland Prairie clay expands and contracts with every wet-dry cycle, and that movement slowly pushes gate posts out of alignment. The motor wears out fighting a gate that was already binding. We fix both problems in one visit, and we hand you a written price before we touch anything. Call (469) 916-7097 and a live person answers, any hour.
Why Plano Homes Are Different
Plano has one of the highest concentrations of automated driveway gates in North Texas, and most of them are hung on brick-veneer homes built from the mid-1980s through the mid-2000s. Those gates were installed on concrete piers, and those piers are the weak point. As the clay soil dries in a Plano summer, it shrinks and the footing settles. When rain or irrigation water returns, the clay swells and pushes the pier upward. The gate frame twists with it. We see this in Willow Bend, in Stonebriar, and in the legacy Craig Ranch tracts, where ornate wrought-iron swing gates that looked perfect in 1998 now sag a half-inch at the latch.
Then there’s the cold. Plano’s ice storms every few winters crack operator housings and shatter keypad displays. Slide-gate drive chains snap in a hard freeze when they haven’t been re-lubricated for cold weather. And the same clay that shifts in summer contracts sharply during a deep freeze, which means a post that barely moved for ten years can shift noticeably in one January week.
West Plano adds one more variable. In the older subdivisions developed in the late 1980s, many swing gates were hung on brick columns instead of steel pipe set in concrete. When the clay moves, those columns crack at the mortar joints. By the time a homeowner calls, the real job is rebuilding the column before the gate hardware can even be addressed.
Our Main Plano Services
Plano homeowners call us most often for three jobs: repairing a gate that no longer opens, installing a new gate, and replacing or servicing the motor. Here’s what each involves in Plano specifically.
Gate Repair in Plano
Gate repair in Plano usually starts with a post that has moved and a frame that binds. We cut the hinge welds, lift the gate, reset the post with new concrete, and weld the hinges back in position. If the gate itself is cracked or rusted at the weld points, we repair or replace those sections rather than condemning the whole unit. Plano’s clay soil means this is a periodic maintenance job, not a one-time fix. Gate Repair in Plano covers the full repair scope and pricing.
Gate Installation in Plano
A new gate in Plano has to be built for the soil it sits on. We set posts deeper than code minimums in Plano because the expansive clay demands it, and we use steel posts set in concrete rather than brick columns for anything heavier than a decorative walk gate. Most Plano installations are wrought-iron swing gates or steel slide gates matched to the home’s architecture. We measure, fabricate, and install with a written price before work starts. Gate Installation in Plano goes through the full process and cost range.
Gate Motor & Opener in Plano
Plano’s hard freezes and summer heat shorten the life of gate operator housings, control boards, and drive chains. We service nine major brands including LiftMaster, DoorKing, and Elite, which means we repair the motor already on the property instead of steering you toward a replacement you don’t need. If the operator is beyond repair, we quote a replacement motor and handle the full wiring and safety-edge adjustment. Gate Motor & Opener in Plano breaks down motor repair and replacement costs for Plano homes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Plano
Plano’s automated gates are often paired with access control systems: keypads, remotes, phone entry, card readers, or video intercoms. The problem here is rarely the gate itself. It’s the entry device that has failed, or the wiring between the device and the operator that has been compromised by a freeze or by ants, which love Plano’s warm operator housings. We find the fault, identify the part, and replace or reprogram it. We follow the same standard we use on every job: a written price before the work, and a documented photo record when we leave. That’s the approach behind our Gate Access Control service.
Keypad Entry
Signs you need it
You enter the code and nothing happens, or the keypad only works intermittently.
What it costs in Plano
Keypad replacement in Plano typically ranges from $180 to $480, depending on the brand and whether the wiring needs to be rerun.
How we do it
We test voltage at the keypad, replace the unit or the wiring as needed, reprogram the codes, and photograph the finished work.
Remote Control
Signs you need it
The remote stopped working, works only from inches away, or a new remote won’t pair to the operator.
What it costs in Plano
Remote programming and replacement in Plano runs from $60 to $180 per remote, depending on the brand and type.
How we do it
We identify the operator brand, pair the new remote, test range, and confirm the old remote no longer works for security.
What Gate Access Control Costs in Plano
| Item | Typical range in Plano |
|---|---|
| Keypad replacement | $180 - $480 |
| Remote programming or replacement | $60 - $180 |
| Phone entry or intercom repair | $220 - $650 |
Can you come today?
Yes. We dispatch technicians across Plano daily, and a live person answers the phone 24 hours a day to schedule it. Call (469) 916-7097 and we’ll tell you when a technician can arrive.
Does a frozen keypad damage the operator too?
Not usually. A cracked keypad is a keypad problem. But a shorted keypad wire can overload the operator’s control board, and that’s a more expensive repair. We check both before quoting anything. Call (469) 916-7097 for a written estimate.
Gate Parts & Welding in Plano
Gate parts and welding in Plano is the repair category most tied to the soil. Hinges tear off when a post leans. Slide-gate rails warp when the embedded track shifts. Wrought-iron pickets crack at the weld when the frame twists. The welding itself is straightforward; the harder part is knowing what caused the failure so the new weld doesn’t tear out the same way next year. That’s exactly the diagnosis we document under our Gate Parts & Welding standard.
Hinge Replacement
Signs you need it
The gate sagging at the latch side, a squeal when it swings, or a visible crack at the hinge weld.
What it costs in Plano
Hinge replacement in Plano typically runs from $140 to $320 per hinge, including cutting the old weld and fabricating a new hinge if needed.
How we do it
We cut the old hinge, weld a new one in place, realign the gate, and document the weld with photos.
Post Replacement
Signs you need it
The post leans visibly, the gate won’t latch, or the concrete footing around the post has cracked and heaved.
What it costs in Plano
Post replacement in Plano costs between $350 and $800 per post, including removing the old footing and setting the new post in concrete.
How we do it
We cut the gate free, dig out the old post and footing, set a new steel post in concrete, and rehang the gate after the concrete cures.
What Gate Parts & Welding Costs in Plano
| Item | Typical range in Plano |
|---|---|
| Hinge replacement | $140 - $320 per hinge |
| Post replacement | $350 - $800 per post |
| Custom welding repair | $120 - $450 |
How long does post replacement take?
A single post replacement is usually a same-day job, but the gate can’t be rehung until the concrete sets. We account for that in the written price and timeline. Call (469) 916-7097 for a quote.
Do you weld wrought iron on site?
Yes. We carry mobile welding equipment and can repair cracked pickets, broken hinge points, and torn rail sections at the property. Call (469) 916-7097 and we’ll tell you if the repair is weldable on site.
Brands We Service in Plano
We work on whatever motor is already on your gate. In Plano, the most common operators we see are LiftMaster, DoorKing, Elite, and Mighty Mule, and we stock common parts for all of them on our trucks. That means most repairs happen in one visit, not two. See our brands for the full list.
Pricing for Gate Repair in Plano, TX
| Service | Typical range in Plano |
|---|---|
| Keypad replacement | $180 - $480 |
| Remote programming or replacement | $60 - $180 |
| Phone entry or intercom repair | $220 - $650 |
| Hinge replacement | $140 - $320 per hinge |
| Post replacement | $350 - $800 per post |
| Custom welding repair | $120 - $450 |
| Rail repair | $180 - $500 |
| Gate roller replacement | $90 - $250 per roller |
Plano’s clay soil is the biggest price variable on structural work. A post that has moved six inches in a single year needs a deeper footing than a post that shifted an inch over a decade. The second variable is access: west Plano’s brick columns sometimes mean we’re rebuilding masonry before we can touch gate hardware.
Every price above is a range, not a commitment. You get a written line-item price before any work starts, and if the job changes, we tell you before we do anything different. No surprise invoice at the end.
Neighborhoods We Serve in Plano
We work throughout Plano, from the west-side subdivisions with their brick-column gates to the newer east-side developments. A representative sample:
- Willow Bend
- Stonebriar
- Legacy Craig Ranch area
- Whiffletree
- Gleneagles
Most Plano calls get a technician on site the same day or the next morning. We confirm the window when you call.
Service Area - Cities Near Plano
We also handle gate repair and installation in the surrounding cities. If you live just outside Plano, call and we’ll tell you if we cover your street. We serve Garland, TX, Wylie, TX, Rowlett, TX, and Dallas, TX with the same written-price, documented-visit standard.
Serving Plano, TX - Our Local Coverage Area
We’re based in the Plano area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Plano
Most Plano addresses get a same-day or next-day visit, depending on when you call. Dispatch is coordinated from our Dallas-Fort Worth office, and crews are staged to cover Plano daily. Call (469) 916-7097 and we’ll confirm a window while you’re on the phone.
Most Plano HOAs require architectural approval for new gates or major changes like post replacement, but not for repairs that restore the gate to its original condition. We always recommend checking your HOA’s rules before structural work begins, and we can help with the paperwork if needed.
The written price covers parts, labor, and the specific work described in the scope. If we find a second problem during the repair, we stop, show you what we found, and give you a revised written price before doing anything else. The number you approve is the number you pay.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Plano Customers Say
"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.